FL SWITCH SFN…
6
Installation
6.2
Removal
CAUTION:
1.
Insert a suitable tool (e.g., needle-nose pliers) into the
arresting latch and pull it down.
Only qualified personnel may start up and operate
this device. Qualified personnel are persons
authorized to start up, ground and mark devices,
systems, and equipment according to the
standards of safety technology.
2.
3.
6.3
Pull the module slightly away from the mounting
surface.
Lift the module from the rail.
Power Connection
NOTE:
The FL SWITCH SFN… module is designed for
SELV and PELV operation according to
The switch is designed for SELV and PELV operation at
+24 V DC according to IEC 61140/EN 61140. Only SELV
and PELV according to the defined standards may be used
for supply purposes.
IEC 61140/EN 61140.
Snapping the switch onto a grounded DIN rail connects it to
WARNING:
A.)THIS EQUIPMENT IS SUITABLE FOR USE IN
CLASS I, ZONE 2, GROUPS A, B, C, AND D OR
NON- HAZARDOUS LOCATIONS ONLY.
B.) WARNING - EXPLOSION HAZARD -
the ground potential. In an environment particularly prone to
EMI, noise immunity can be increased by an additional low-
impedance connection to functional earth ground.
SUBSTITUTION OF COMPONENTS MAY
IMPAIR SUITABILITY FOR CLASS I, ZONE 2.
C.) WARNING - EXPLOSION HAZARD - DO
NOT DISCONNECT EQUIPMENT UNLESS
POWER HAS BEEN SWITCHED OFF OR THE
AREA IS KNOWN TO BE NON-HAZARDOUS.
Install the FL SWITCH SFN… on a clean DIN rail. To avoid
contact resistance use only clean, corrosion-free rails that
+
meet the EN 50022 standard. End clamps should be
mounted on both sides of the module to stop the modules
from slipping on the rail.
US GND
6.1
1.
2.
3.
NOTE:
Connect the DIN rail to protective earth ground
using a grounding terminal block. The modules
are grounded when they are snapped onto the
rail. Connect protective earth ground with low
impedance. 1000 Mbps switches have a
protective ground connecting screw on top.
Assembly
Place the module onto the DIN rail from above. The
upper holding keyway must be hooked onto the top
edge of the DIN rail.
Push the module from the front towards the mounting
surface.
Once the module has been snapped on properly, check
that it is fixed securely on the rail.
Figure 3
FL SWITCH SFN…TX… power connection
2732_en_D
PHOENIX CONTACT
8
相关PDF资料
29-4010 CONN MINI-UHF PLUG CRIMP RG-58
29-4033 CONN MINI-UHF PLUG CRIMP RG-8X
2920L150DR PTC RESET 33V 1.50A SMD 2920
292204-3 CONN CARD EDGE 8POS DL 2MM GOLD
292303-2 CONN USB TYPE A R/A PCB
292304-4 CONN USB RCPT TYPE B R/A PCB
292317-4 CONN RCPT USB TYPE B PCB R/A
292323-3 CONN RCPT USB TYPE A R/A DBL
相关代理商/技术参数
2891424 功能描述:以太网和电信连接器 FL PATCH GUARD RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级:
2891440 制造商:Phoenix Contact 功能描述:FL IP 54 SPOUT
2891444 功能描述:ETHERNET SWITCH 制造商:phoenix contact 系列:- 零件状态:有效 类型:交换机 - 非托管型 配置:固定式 端口数:5 铜端口:5 铜类型:10/100/1000 光纤端口:- 光纤类型:- SFP/XFP 端口:- SFP/XFP 型:- PoE 端口:- 连接器类型:RJ45 电压 - 输入:10 ~ 60VDC 侵入防护:IP20 安装类型:DIN 轨道 工作温度:-10°C ~ 60°C 标准包装:1
2891453 功能描述:以太网模块 FL SWITCH SFN 4TX RoHS:否 制造商:Lantronix 产品:Device Servers 数据速率:300 bps to 921.6 kbps, 10 Mbps, 100 Mbps 接口类型:Ethernet, Serial 工作电源电压:5 V to 15 V 工作电源电流:133 mA to 400 mA 最大工作温度:+ 70 C
28-91457 制造商:Johnson Components 功能描述:CONN BNC M 75OHM CRMP ST CBL MNT - Bulk 制造商:Emerson Connectivity Solutions 功能描述:BNC 3-PC CRIMP PLUG BELDEN 9248, 1694A
2891466 功能描述:以太网模块 FL SWITCH LM 8TX-E RoHS:否 制造商:Lantronix 产品:Device Servers 数据速率:300 bps to 921.6 kbps, 10 Mbps, 100 Mbps 接口类型:Ethernet, Serial 工作电源电压:5 V to 15 V 工作电源电流:133 mA to 400 mA 最大工作温度:+ 70 C
2891479 功能描述:以太网模块 FL SWITCH SMCS 6GT/2SFP RoHS:否 制造商:Lantronix 产品:Device Servers 数据速率:300 bps to 921.6 kbps, 10 Mbps, 100 Mbps 接口类型:Ethernet, Serial 工作电源电压:5 V to 15 V 工作电源电流:133 mA to 400 mA 最大工作温度:+ 70 C
2891482 功能描述:电缆组件 FL CAT6 PATCH 1.5 RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规(AWG):20, 28 长度:0.305 m 颜色:Black, Red